BETONBLOCK® plán postupu

BETONBLOCK® plán postupu

  • Pozrite si naše pracovné postupy:
  • Systém BETONBLOCK® je naozaj úplný; všetky potrebné produkty a príslušenstvo nájdete na jednom mieste.
  • Vylievanie betónovej tvárnice alebo dosky do formy je jednoduché. Výsledok? Super tesné!
Casting step 1

Krok 1 – Položte prázdnu formu na rovný povrch

Položte formu BETONBLOCK® na rovný povrch, napr. na oceľovú dosku alebo na stôl na vylievanie.

Casting step 2

Krok 2 – Naneste náter

Naneste olejový náter, aby sa neskôr vytvrdnutý blok dal ľahko uvoľniť z formy

Casting step 3

Krok 3 – Odlievanie

Betón sa leje postupne, čím sa vytvára vynikajúca výplň aj vo výčnelkoch.

Casting step 4

Krok 4 – Miešanie vibrovaním

Zároveň sa betón mieša pomocou elektrického alebo pneumatického vibrátora, aby sa zabezpečilo homogénne zhutnenie betónu.

Casting step 5

Krok 5 – Vyhladenie

Po úplnom vyplnení a zamiešaní vo forme sa betón uhladí hladidlom. Teraz nechajte betón vytvrdnúť v závislosti od typu betónu a podmienok.

Casting step 6

Krok 6 – Odstránenie kolíkov a klinov

Po vytvrdnutí betónu môžete formu opäť otvoriť. Začnite odstránením kolíkov a klinov, aby sa forma dala otvoriť.

Step 7 casting  Open Mould

Krok 7 – Otvorenie formy

Po odstránení kolíkov a klinov stačí otvoriť formu a odstrániť steny.

Casting ready

Hotovo!

Po odstránení foriem je váš výrobok BETONBLOCK® hotový. Rýchle, jednoduché a... vždy rovnaká kvalita, rozmery a tvar!

 

Práca so systémom BETONBLOCK® je taká jednoduchá. Pozrite si video!
 

 

  • Anchors, how do you place them?
  • We explain this below in 8 steps
  • Sometimes a picture says more than a thousand words
Stappenplan ankers 1

Step 1 - Place the magnet (BBMAG01) in the middle center? of the mold

Stappenplan ankers 2

Step 2 - Place the rubber (BBGRO02) around the anchor (BBHA025)

Stappenplan ankers 3

Step 3 - Place the anchor with the rubber in the magnet

Stappenplan ankers 4

Step 4 - The anchor is cast in its entirety, be careful when vibrating the concrete

Stappenplan ankers 5

Step 5 - When the mold is opened, the magnet remains in the mold

Stappenplan ankers 6

Step 6 - Remove the rubber from the anchor

Stappenplan ankers 7

Step 7 - Only the top of the anchor is now visible

Stappenplan ankers 8

Step 8 - Attach the hooks to the anchors and the load is ready to be lifted

BT2500 Handleiding 00

INSTRUCTION MANUAL BT2500 

Product description
Block Turner. The concrete block turner has been especially designed to turn concrete blocks without damaging them. The blocks are casted on their side and the block turner easily moves them into the upright position. The engine handler uses a remote control and the hydraulic block-turner tilts the block 90 degrees. This set contains: • BT2500 Block Turner • Remote Control • User Guide & Quick Guide.

The following steps will guide you to quickly set-up your Betonblock remote for your BT2500.

BT2500 Handleiding 01

1. Unpack BT2500
Your BT2500 arrives wrapped up tight so it can’t move during transport. Remove the strap before use.
It has been pre-installed, so in general there is no need to change the settings.

BT2500 Handleiding 02

2. Setup before use
First release the emergency break.
Switch on the BT2500 by flipping the black switch. The led indicator should turn green. The device is now ready for use.

BT2500 Handleiding 03

3. Remote setup
To start using the remote, press the switch on the rear side to forward position.
Attention: While pressing the upper/lower button, aim for the right side of the BT2500 where the infrared detector is located.

BT2500 Handleiding 04

4. Getting ready to start
To start using the BT2500, press the upper button to turn the device in upright position. It should open until straight. If not, press upper button again.
Use a clamp to place a block on the BT2500 and press the upper button again.
Attention: The machine won’t lower without a block!

BT2500 Handleiding 05

5. Turning the block
When the block lowers, the BT2500 needs 20 seconds before remaining in a locked down position. If the handler is ready beforehand press the lower button to lock the low position. Then clamp the block with the BETONBLOCK® Clamp.
Attention: The BT2500 will move to the upright position if a block is removed within 20 seconds or without pushing the lower button.

BT2500 Handleiding 06

6. Clamping the turned block
Clamp the block when the system is in lockdown position (after 20 seconds or after pressing the lower button). Then remove the block.

Skúsenosti so systémom BETONBLOCK®?